null

HOOKER BLACKHEART

Hooker Blackheart Gen V LT-Swap Exhaust Manifolds - 2.50" Rear Dump SBC Exit / Black

PART NUMBER:
BHS5198
MPN:
BHS5198
Availability:
Ships from Manufacturer
Shipping:
Free Over $98 In U.S. 48
Type:
LT Swap Exhaust Manifolds
Application:
Multi-Fit
Material:
Cast Iron
Finish:
Black
Engine:
GM Gen V (LT Based)
Collector Dia. (In.):
2-1/2
Primary Tube Dia. (In.):
1-3/4
Bolt Size:
M8 x 1.25 x 25mm
Mounting Hardware Included:
Yes
Notes:
Not compatible with 2004-2006 GTO starters/bellhousings
  • Hooker Blackheart Gen V LT-Swap Exhaust Manifolds - 2.50" Rear Dump SBC Exit / Black (BHS5198)
  • Hooker Blackheart Gen V LT-Swap Exhaust Manifolds - 2.50" Rear Dump SBC Exit / Black (BHS5198)
  • Hooker Blackheart Gen V LT-Swap Exhaust Manifolds - 2.50" Rear Dump SBC Exit / Black (BHS5198)
  • Hooker Blackheart Gen V LT-Swap Exhaust Manifolds - 2.50" Rear Dump SBC Exit / Black (BHS5198)
  • Hooker Blackheart Gen V LT-Swap Exhaust Manifolds - 2.50" Rear Dump SBC Exit / Black (BHS5198)
  • Hooker Blackheart Gen V LT-Swap Exhaust Manifolds - 2.50" Rear Dump SBC Exit / Black (BHS5198)
  • Hooker Blackheart Gen V LT-Swap Exhaust Manifolds - 2.50" Rear Dump SBC Exit / Black
  • Hooker Blackheart Gen V LT-Swap Exhaust Manifolds - 2.50" Rear Dump SBC Exit / Black (BHS5198)
  • Hooker Blackheart Gen V LT-Swap Exhaust Manifolds - 2.50" Rear Dump SBC Exit / Black
  • Hooker Blackheart Gen V LT-Swap Exhaust Manifolds - 2.50" Rear Dump SBC Exit / Black (BHS5198)
$499.95

Description

Hooker Blackheart Gen V LT-Swap Exhaust Manifolds - 2.50" Rear Dump SBC Exit / Black

Multi-Fit - GM Gen V LT Engines - 2.50-in. Outlet

For applications or projects where our standard LT swap manifolds (BHS516 and BHS3116) don't quite fit and our "center dump" manifold (BHS5188) exits too far forward, our new rear dump and rear dump SBC exit cast iron swap manifolds have arrived. These differ in that they exit in a straight-down fashion much like a block hugger header but exit more toward the rear of the engine than our "center dump" manifolds. While almost the same as our BHS5192/93/94, the BHS5196 shares the same driver side manifold, but has the passenger side exit of traditional Small Block Chevrolet manifolds (see 8525HKR) to guarantee fitment and possibly bolt up your existing exhaust when doing an LS swap. Cast out of the same Hi-Silicon-Moly Ductile Iron as most of our other lines, it will be tough to find a more durable, streamlined, and quiet exhaust option. Available in natural cast, silver ceramic, or black ceramic finishes, these manifolds are offered with flanges, gaskets, and flange hardware for connecting to our lineup of adapter pipe kits or for ease in fabricating your own custom exhaust.

Features:

  • Similar to SBC manifolds (8525HKR) but for Gen V LT engines - same exit centerline but raised up 1.36-inches (driver side) / tucked in tighter by 0.625-inches on (passenger side)
  • 2.5-inch outlet diameter offers improved flow for maximum performance from a cast iron exhaust manifold
  • Tight tuck design that provides an exit between our standard swap manifolds and center dump manifolds (with passenger side SBC exit)
  • Intended for GM LT engine swap applications where durability, quiet operation, and leak-free sealing is desired
  • Available in Natural as-cast finish for a factory appearance, silver ceramic, or black ceramic
  • Cast from Hi-Silicon-Moly Ductile Iron to provide durability and corrosion resistance
  • Perfect complement to Hooker engine swap mount plates and Holley engine swap oil pans
  • Hardware included: Nickel plated steel mating flanges, MLS mating flange gaskets, and mating flange hardware
Application Multi-fit
Bolt Size M8 x 1.25 x 25mm
Brand Hooker BlackHeart
Choose Your Part Manifold
Collector Diameter 2.50 inch
Emission Code 8
Engine GM Gen V (LT Based)
Exhaust Manifold Style Rear Dump SBC Exit
Exhaust Series Hooker
Finish Black Ceramic
Flange Style 2-Bolt
Header Finish Natural
Header Style Manifold
Material Cast Iron
Primary Tube Dia. 1-3/4 inch
Product Type Manifold
Subframe Stock
Tube Material Cast Iron
Type of Component Manifold
Part Number BHS5198
NOTE: Not compatible with 2004-2006 GTO starters/bellhousings. Breaking in an engine with ceramic-coated versions of these manifolds will most likely result in damage to the coating and VOID all warranties providing coverage to it. HOOKER™ recommends using bare cast-iron manifolds or an old set of headers to break-in engines to avoid coating damage. Ceramic-coated manifolds require several heat cycles to fully cure before they will withstand extreme heat, so care should be taken to provide a series of 4 to 5 intermittent heat cycles to "set" the coating prior to putting the vehicle into service. An incremental increase in run duration and throttle angle should be added to each successive cycle; initial and final run durations between approximately 1 and 7 minutes will be sufficient to set the coating.
View AllClose

Warranty Information

Hooker BLACKHEART 304 stainless steel exhaust products are covered by a limited lifetime warranty that covers certain defects in workmanship and materials. Who is covered? This warranty covers the original purchaser of Hooker BLACKHEART 304 stainless steel exhaust products in the United States and Canada. What is covered and for how long? Holley Performance Products Inc. (Holley) warrants that Hooker BLACKHEART 304 stainless steel exhaust products will be free from defects in material and workmanship for the life of the product on the original car on which it was installed. Blemishes, marring of appearance, discoloration, internal rust, or surface rust due to weather, road hazards, lack of maintenance, or extremes of heat of cold are not be considered defects under this Limited Lifetime Warranty. Holley warrants moving parts such as valves and actuators for three years. All claimed warranty products must have a return goods authorization (RGA) number and shipped to Holley at the buyers expense. The returned product must be accompanied with a copy of the original purchase receipt and the original purchasers contact information. What will Holley do? If there is a defect in material or workmanship, Holley will choose either to repair the defective part or replace it with a comparable, new part, without charge for the repair or the replacement product. Purchasers remedies under this Limited Lifetime Warranty are strictly limited to the repair or replacement of the defective product. You must pay the cost of shipping the product back to Holley and for any labor or other costs, including any additional parts, associated with removing the allegedly defective part and with the installation of the repaired or replacement part. What is NOT covered? This warranty does not cover Hooker BLACKHEART stainless steel products that have been installed on any commercial or racing vehicle or that have been damaged due to misuse, abuse, neglect, or accident, such as having been modified or altered; improperly installed, adjusted or repaired; welded; exposed to corrosion, corrosive materials, other contaminants; or used in applications other than those recommended by Hooker on our website (www.holley.com). How do I start the warranty claim process? To initiate the return process under this Limited Lifetime Warranty, please contact our customer service team immediately at 800-638-0032 and hit customer service option or email at holleyorders@holley.com for complete Hooker BLACKHEART product return instructions and to request a Return Goods Authorization (RGA) Number. Please be prepared to return the allegedly defective product to Holley, along with a copy of the original dated purchase receipt. Holley reserves the right to reject a warranty claim if you cannot establish date of purchase. Final warranty determination is at the sole discretion of Holley. Should I use Header Wraps? If you choose to use header wraps, you will void your Warranty. Header wraps cause fatigue in the primary tubes and create fractures in the metal. What other conditions and exclusions apply? This warranty does not provide compensation for loss of time, loss of use of vehicle, labor cost, cost of additional parts, shipping, inconvenience or other consequential or incidental damage. Some states do not allow the exclusion or limitation of incidental or consequential damages, so these limitations or exclusions may not apply to you. Holleys maximum liability under this Limited Lifetime Warranty shall not exceed the original cost of the product to the consumer. This Limited Warranty gives you specific legal rights and you may also have other rights which vary under state or provincial laws. This Limited Warranty is exclusive and in lieu of all others, whether oral or written and whether express or implied. Any implied warranties, including implied warranties of merchantability and fitness for a specific purpose are hereby disclaimed. Some states do not allow the exclusion or limitation of implied warranties, so these exclusions or limitations may not apply to you.
View AllClose